POSTEROVÁ SEKCE B

Datum: 23.5.2019

PB1
BEDNARCZYK Iwona
Silesian University of Technology, Gliwice, Poland, EU
The Microstructure and Properties of Magnesium Alloys after Deformation Process with the Use of KoBo Method - POSTER
PB2
BIŚ Jesica
Częstochowa University of Technology, Częstochowa, Poland, EU
Theoretical Analysis of the Rolling Process of a Thick-walled Thimble in an Elongating Mill - POSTER
PB3
BRUSILOVÁ Alena
Slovak University of Technology in Bratislava, Bratislava, Slovakia, EU
Optimization of Tubes Bending and Their Properties with Abrasion Resistance Cast Iron Tool Using - POSTER
PB4
DJIMAOUI Toufik
University of Biskra, Biskra, Algeria
The Effect of Drawin on the Residual Stresses and Evolution of Mechanical Properties in Low Carbone Steel - POSTER
PB5
DUCKI Kazimierz
Silesian University of Technology, Katowice, Poland, EU
The Characteristic of Deformability and Quantitative Description of Microstructure of Hot-Deformed IN 718 Superalloy - POSTER
PB6
EIVANI Ali Reza
Iran University of Science and Technology, Tehran, Iran, Islamic Republic of
An Investigation of Flow Localization during Hot Deformation of Sn-5Sb Solder Alloy - POSTER
PB7
FRANCZAK Krystian
AGH University of Science and Technology, Cracow, Poland, EU
Numerical Analysis of the Non-waste Forging Process of Welding Caps Intended for the Resistance Welding Process - POSTER
PB8
HADASIK Eugeniusz
Silesian University of Technology, Katowice, Poland, EU
Structure and Mechanical Properties of Rolled Bars from Steel 42CrMo4 - POSTER
PB9
HYRCZA-MICHALSKA Monika
Silesian University of Technology, Gliwice, Poland, EU
Results of Searching for Innovative Solutions to Increase the Formability of Thin Sheets in the Deep Drawing Process of Vehicle Components - POSTER
PB10
IWANIEC Radosław
AGH University of Science and Technology, Nowy Sącz, Poland, EU
Single Point Incremental Sheet Forming of Alloys Used in Aerospace Industry - POSTER
PB11
JABŁOŃSKA Magdalena Barbara
Silesian University of Technology, Gliwice, Poland, EU
Investigation of Properties of Structural Steels Deformed at Dynamic Conditions - POSTER
PB12
KANDER Ladislav
MATERIÁLOVÝ A METALURGICKÝ VÝZKUM s.r.o., Ostrava, Czech Republic, EU
Effect of Forging Ratio on Microstructure and Grain Size of the Structural Steel Used for Special Applications - POSTER
PB13
KAWULOK Petr
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
The High-temperature Strength and Plastic Properties of Selected Low-alloyed Cr-Mo Steels - POSTER
PB14
KOREČEK David
Technical University of Liberec, Liberec, Czech Republic, EU
Research of the Temperature Influence on the Change of Titanium Alloy Mechanical Properties by Means of the Optical Contact-less Analysis - POSTER
PB15
LESZCZYSŃSKI Jacek
Silesian University of Technology, Mikolow, Poland, EU
Optimization of the Straightening Process with the Roller Levelers for High-strength Plates in Continuous Systems - POSTER
PB16
CIEŚLA Marek
Silesian University of Technology, Katowice, Poland, EU
Operational Characteristics Tube Bends of X10CrWMoVNb9-2 Steel Made in the Bending Process with Local Induction Heating - POSTER
PB17
MIKUŁA Jarosław
Silesian University of Technology, Gliwice, Poland, EU
Dynamic Method of Percussive Burnishing used for Improvement of the Hydraulic Actuators Performance - POSTER
PB18
MIŁEK Tomasz
Kielce University of Technology, Kielce, Poland, EU
Variations of Microhardness in Longitudinal Sections of Hydroformed Axisymmetric Components Made from P265TR1 Steel - POSTER
PB19
MOSES Marie
TU Bergakademie Freiberg, Institute of Metal Forming, Freiberg, Germany, EU
Twin-roll Casting of Magnesium Wire: an Innovative, Continuous and Cost-efficient Production Route - POSTER
PB20
NASERSANI Alireza
Ferro Gilan Complex, Rasht, Iran, Islamic Republic of
Improving Heat Treatment Processes for ST22 and ST24 and ST 37 Steel Strips so as to Reduce Sticky Layers - POSTER
PB21
NAVRÁTIL Horymír
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Comparison of Hot Deformation Behavior of Superalloys Inconel 600 and Incoloy 825 - POSTER
PB22
NOVÁK Vít
Czech Technical University in Prague, Prague, Czech Republic, EU
The Effect of Strain Rate on Position of Forming Limit Curve - POSTER
PB23
OPĚLA Petr
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
A Hot Flow Curve Approximation via Biology-Inspired Algorithms - POSTER
PB24
REŠKOVIĆ Stoja
University of Zagreb Faculty of Metallurgy Sisak, Sisak, Croatia, EU
The Influence of Niobium Precipitates in the Cold Drawing Pipe - POSTER
PB25
RODAK Kinga
Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, Katowice, Poland, EU
Hypoeutectic Al-Cu Alloys Subjected to Severe Plastic Deformation - POSTER
PB26
RUSZ Stanislav
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Determination of the Hot Deformation Activation Energy and Flow Stress Course of the AISI 4140 Steel - POSTER
PB27
RUSZ Stanislav
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Influence of Severe Plastic Deformation Process on Mechanical Properties of Low Carbon Steel - POSTER
PB28
SEVOST'YANOV Mikhail Anatol'yevich
IMET RAS, Moscow, Russian Federation
The Production of a Thin Wire of Non-nickel Shape Memory Alloy for Medical Devices - POSTER
PB29
SCHREK Alexander
Slovak Unviersity of Technology, Bratislava, Slovakia, EU
Technological Process Simulation for Producing of Bimetallic Billet - POSTER
PB30
SOBOTKA Jiří
Technical University of Liberec, Liberec, Czech Republic, EU
Determination of the Temperature Influence on the Change of Young’s Modulus - POSTER
PB31
SZKANDERA Pavel
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Increasing of Mechanical Properties by SPD Process - POSTER
PB32
TILL Jakub
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Microstructure and Tensile Properties of Brass Formed by Combination of DRECE and CGP - POSTER
PB33
TOMASZEWSKA Agnieszka
Silesian University of Technology, Katowice, Poland, EU
The Effect of Cold Drawing on Properties and Microstructure of Manganese Austenitie Steel Wire - POSTER
PB34
URSINUS Jonathan
Institute of Forming Technology and Machines, Garbsen, Germany, EU
Hot Forming of Cast Steel Cylinders - POSTER
PB35
VALEŠ Michal
Czech Technical University in Prague, Prague, Czech Republic, EU
Outer Car Body Panels made of Dual-Phase Steel - POSTER
19:30 - 19:45
ANNOUNCEMENT OF THE BEST POSTER CONTEST

Zpět